THE ART OF BASIC PLUMBING WHEN YOU INSTALL A BATHTUB

The Art of Basic Plumbing When You Install a Bathtub

The Art of Basic Plumbing When You Install a Bathtub

Blog Article

Estimate

They are making a number of great pointers on How to Install a Bathtub Yourself in general in the article beneath.


How to Install a Bathtub Yourself
Setting up a tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is likewise a reasonably tough project. If the old tub is conveniently accessible, the project can move rapidly; if you need to open a wall to remove the old tub and also position the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified yourself for the task and also fit attempting it. Rather than employing a professional to take over a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will assist you install a brand-new bath tub in your restroom if you have already purchased a new bathtub and don't need to alter the plan of your previous water pipelines.
Your devices as well as product checklist need to comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    First of all, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to avoid stress on the tub.
    Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last setting.

    Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the supply of water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited gain access to that is often the instance.
    Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
    Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Setting up the Bathtub


    Using the two wooden boards under its feet, position the bath tub in the required placement. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
    The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub until the spirit level reads degree.
    To mount taps, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
    Activate the water and also check all joints as well as new pipework for leaks and also tighten them if needed. Fill the tub and likewise examine the overflow electrical outlet and the regular electrical outlet for leaks.
    Finally, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bath tub has been used at the very least when as this will certainly settle it into its final position.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in place with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a stiff seal, creating the water to permeate the wall in between the bathroom and the tiling, causing issues with moisture and feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this movement before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles utilizing waterproof or waterproof glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I have been very taken with How to Install a Bathtub Yourself and I'm hoping you appreciated the entire blog post. Those who enjoyed our post if you please don't forget to share it. Thank you so much for taking the time to read it.


    Quick solution? Call.

    Report this page